NX-5300

nx-5300

 

Kenwood’s first dual-mode portable and mobile radios that will operate on either the NXDN or P25 network, the ground-breaking NX-5000 series.

 

Main Features

  • Multi-Digital operation in P25 (Phase 1 & 2) and NXDN™ protocols
  • Mixed Digital & FM Analog Operation allows intelligent migration in mixed sites and easy migration with digital radios in other sites
  • Large, Color 1.74″ (240 x 180 pixels) Transflective TFT Display for better interface even in direct sunlight and with use of polarized sunglasses.
  • Easy to follow GUI for at-a-glance operational status checking and Multi-line Text to convey more information
  • 4-way Directional-pad (D-pad) and 2-Position Lever Switch for intuitive control and operation
  • Built-in GPS Receiver / Antenna for effective fleet management
  • Bluetooth® Module built-in for hands-free operation
  • Active Noise Reduction (ANR) utilizing built-in DSP with two microphones for suppression of ambient noise
  • Renowned KENWOOD Digital Audio Quality
  • Built-in 56-bit DES Encryption
  • Optional 256-bit AES Encryption
  • Built-in Motion Sensor for life-critical man-down detection
  • microSD / microSDHC Memory Card Slot for increased memory capacity for “Voice & Data”
  • Intelligent battery system (Option)

    •  

     

    General Features

    ◆ VHF: 136-174 MHz (NX-5200)
    ◆ UHF: 380-470 MHz, 450-520 MHz, (NX-5300)
    ◆ 700-800MHz: RX: 763-776, 851-870MHz TX: 763-776, 793-806, 806-825, 851-870MHz (NX-5400)

  • RF Output

    • ◆ VHF: 5 W (NX-5200)
    ◆ UHF: 5 W (NX-5300)
    ◆ 700-800MHz: 3 W (NX-5400)

  • Maximum of 4,000 CH / Radio capacity, 512 CH / Zone, 128 Zones
  • 6 Front & 2 Side PF keys
  • 12-Key Keypad Models Available
  • Emergency / AUX Key
  • Color 1.74″ (240 x 180 pixels) Transflective TFT Display
  • Color GUI and Multi-line Text Display
  • 1 W “Laud” Speaker Audio
  • MIL-STD-810 C / D / E / F / G
  • IP54 / 55 (Dust & Water) IP67 / 68 (2 hours at a depth of 1 meter)

    •  

    P25 Mode

  • P25 Conventional / Trunked
  • (Phase 1 / Phase 2) Protocol
  • AMBE+2™ Enhanced Vocoder
  • Talk Group ID Lists
  • Individual ID Lists
  • Caller ID Display
  • Remote Monitor / Remote Check
  • Radio Inhibit
  • Encryption Key Zeroize & Retention
  • P25 GPS Location
  • P25 Over-the-Air Re-keying
  • P25 Over-the-Air Programming*2

    •  

    NXDN Mode

  • NXDN™ Conventional / Trunked Protocol*1
  • AMBE+2™ Enhanced Vocoder
  • 6.25 & 12.5 kHz Channel Spacing
  • Over-the-Air Alias
  • Over-the-Air Programming*2
  • Paging Call
  • Emergency Call
  • All Group Call
  • Status Messaging*3
  • Remote Stun / Kill*3
  • Remote Check*3
  • Short & Long Data Messages*3
  • GPS Location
  • NXDN™ Digital Scrambler Included

    •  

    *1: Only supports TYPE-C Protocol
    *2: Requires KENWOOD OTAP Management software.
    *3: Requires NX subscriber unit PC serial interface compatible software application (e.g. KENWOOD AVL & Dispatch Messaging software) or hardware (e.g. console)

     

    Analog Mode

  • Conventional & LTR® Zones
  • FleetSync® / II : PTT ID ANI / Caller ID Display, Selective / Group Call, Emergency Status / Text Messages
  • MDC-1200 : PTT ID ANI / Caller ID Display, Emergency, Radio Check / Inhibit
  • QT / DQT & Two-Tone
  • Built-in Voice Inversion Scrambler

    •  

    Part Number

    NX-5300